Getting Familiar with Plumbing: A Must for Installing a Bathtub
Getting Familiar with Plumbing: A Must for Installing a Bathtub
Blog Article
The article below in relation to A Step-by-Step Guide to Installing a Bathtub is amazingly compelling. Read it for yourself and decide what you think about it.
Setting up a bath tub isn't specifically rocket science, yet it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old bathtub is readily accessible, the project can move quickly; if you need to open a wall to get rid of the old bathtub and also position the new bath tub, the task is a lot harder. In either instance, the job is within a residence handyman's skills, although you will need an assistant to vacate the old tub as well as embeded in the brand-new one. Ensure you have actually qualified yourself for the task as well as fit trying it. Rather than hiring a specialist to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This article will aid you mount a new bathtub in your washroom if you have currently acquired a new tub and also do not require to alter the plan of your previous supply of water pipelines.
Your tools and also product list should consist of the following:
Preparing for the Installation
First of all, the sustaining structure provided with the bath should be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to avoid stress on the bath tub.
Fit the adaptable tap ports to the bottom of both taps using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is separate the water. After doing so, activate the faucets to drain any water remaining in the system. The procedure of removing the existing taps can be fairly problematic due to the restricted access that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a cloth ready for the staying water that will come from the pipelines. Once the supply pipes have actually been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single taps from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing compound.
Before proceeding to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the bathtub in the required placement. The wood boards are practical in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four tiny factors.
The following goal is to make sure that the bathtub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the tub until the spirit level reads level.
To mount faucets, fit the bottom of the outermost adaptable tap port to the ideal supply pipeline by making a compression join; then do the exact same for the various other faucet.
Turn on the supply of water and also inspect all joints as well as new pipework for leaks as well as tighten them if necessary. Load the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's instruction manual. Tiling and sealing around the bathtub should wait until the bath tub has been utilized at the very least once as this will certainly settle it into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damage to the thread. One end of the port fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location in between the tap and the sink. Safeguard the tap in place with the manufacturer provided backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to split an inflexible seal, creating the water to pass through the wall surface between the bath and the tiling, resulting in problems with dampness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures as well as installations. They are marketed in tubes and cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the bathtub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealant can crack fairly early if you do not take into account this activity before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise easily readily available on the marketplace. It is recommended to fit the floor tiles using water-resistant or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about How to Install a Bathtub? Place a comment below. We'd be interested to find out your views about this blog entry. We are looking forward that you visit us again soon. Appreciated our article? Please share it. Help someone else check it out. Thank you for going through it.
Visit Our Site Report this page